MB5 1512173.jpg ..jpg DSCF5503.jpg

Author Topic: Messerschmitt Me262 in 1/144th  (Read 149 times)

Bigkev

  • Administrator
  • Hero Member
  • *****
  • Posts: 2011
    • View Profile
Re: Messerschmitt Me262 in 1/144th
« Reply #15 on: October 12, 2019, 05:09:48 PM »
Well, managed to mask the upper surfaces in readiness for tomorrow's painting session.
As mentioned beforehand I think the colour descriptions have been transposed, so opposed to my usual approach the lighter green will be sprayed next.
Once done further smaller blotches of both colours will be added to the fuselage sides and wing surfaces.
A few pictures follow.
Bigkev

Bigkev

  • Administrator
  • Hero Member
  • *****
  • Posts: 2011
    • View Profile
Re: Messerschmitt Me262 in 1/144th
« Reply #16 on: October 13, 2019, 05:23:08 PM »
Hi All,
Well the rain has meant I'm allowed in the modelling room!
So I have managed to give the upper surface's a coat of RLM 83 'Olivgrun'. All went well, and the Aeromaster paint sprayed beautifully, despite being 20 years old.
Once dry, I peeled off the masking. The tape was no problem, but the Blu-Tack worms meant a little more work. they did not peel off in one motion, but needed several passes with a bigger piece of Blu-Tack to remove the material completely.
Once done I was left with quite a nice demarcation line, on both wings and fuselage.
Some pictures follow.
Bigkev 

Bigkev

  • Administrator
  • Hero Member
  • *****
  • Posts: 2011
    • View Profile
Re: Messerschmitt Me262 in 1/144th
« Reply #17 on: October 13, 2019, 05:29:07 PM »
Hi All,
Whilst waiting for the main airframe to dry properly, I took the opportunity of painting the Kettenkrad and towing arms, plus the insides of the undercarriage doors.
All painted using Aeromaster paint, which being water based made for easy application and clean up.
A few pictures follow.
Bigkev
 

Bigkev

  • Administrator
  • Hero Member
  • *****
  • Posts: 2011
    • View Profile
Re: Messerschmitt Me262 in 1/144th
« Reply #18 on: October 13, 2019, 05:36:54 PM »
Hi All,
Well after all that masking had been removed, and paint allowed to dry, I decided I could tackle the mottle camouflage on the fuselage sides and engine cowlings. It took a few go's, having to re-cover some bits that were too heavy, or had indications of airbrush splatter. A few hours later I was happy with the result, and I am now ready to paint the undercarriage bays in RLM 02 Grey, then apply a gloss 'Future' varnish to seal everything in ready to deaclling.
A few pictures follow:-
Bigkev
« Last Edit: October 14, 2019, 03:21:59 AM by Bigkev »

Bigkev

  • Administrator
  • Hero Member
  • *****
  • Posts: 2011
    • View Profile
Re: Messerschmitt Me262 in 1/144th
« Reply #19 on: October 16, 2019, 07:42:54 PM »
Hi All,
Well a bit further on now.
Managed to paint in the red trim on the nose and tail.
Also I have applied 3 thin coats of Johnson's 'Kleer' to the airframe ready for decaling. However, I kept the 'Kleer' off the canopy parts, so as not to create a build up on the canopy frames. Once decalled, I will apply a final Matt/Satin coat to the whole airframe, including the canopy so there will be no apparent difference in finish..... I hope!
Decaling next...
Some pictures follow:-
Bigkev

Haddock

  • Hero Member
  • *****
  • Posts: 1448
    • View Profile
Re: Messerschmitt Me262 in 1/144th
« Reply #20 on: October 17, 2019, 10:18:10 AM »
Looking nice. Is the Klear brushed or airbrushed?
Haddock.

Bigkev

  • Administrator
  • Hero Member
  • *****
  • Posts: 2011
    • View Profile
Re: Messerschmitt Me262 in 1/144th
« Reply #21 on: October 17, 2019, 07:05:26 PM »
Hi Haddock,
Thankyou for your comment, yes, it is coming along nicely now..
As to the 'Kleer' I always use a number '6' size brush. But I find that it works better if you wet the brush thoroughly in warm water, then squeeze out most of water before dipping it in the 'Kleer'. Then it is just a case of quick light coats, allowing about an hour between coats.
Cheers,
Bigkev

Bigkev

  • Administrator
  • Hero Member
  • *****
  • Posts: 2011
    • View Profile
Re: Messerschmitt Me262 in 1/144th
« Reply #22 on: Today at 06:49:04 AM »
Hi All,
A bit more progress. The decals have been applied, using the Micro Set and Micro Sol solution's.
A quick check revealed a couple of areas where silvering occurred despite the gloss finish. So using a hypodermic needle, I pricked the areas involved and applied some more Micro Sol.
Once dried, I will give the model a wash with a warm soapy piece of cloth, followed by a quick rinse, to remove any excess solution's, and then it is time for the varnish.
Some pictures to show:-
Bigkev   :D

Roger

  • Hero Member
  • *****
  • Posts: 387
    • View Profile
Re: Messerschmitt Me262 in 1/144th
« Reply #23 on: Today at 08:48:04 AM »
Lovely, looks just right.

Roger